Dinver: Tools menu - Revision history

Marc at 13:58, 12 March 2010

2010-03-12T13:58:03Z

Marc: Dinver:Menus:Tools moved to Dinver: Tools menu

2010-03-12T13:12:23Z

Dinver:Menus:Tools moved to Dinver: Tools menu

Marc at 21:13, 26 November 2008

2008-11-26T21:13:59Z

Marc at 21:13, 26 November 2008

2008-11-26T21:13:19Z

Marc: New page: This menu lets the user hide or show various tools used along inversions. It contains at least three items which content is the same for all inversion modules: * Runs * Log * Status Plus ...

2008-11-26T21:12:09Z

New page: This menu lets the user hide or show various tools used along inversions. It contains at least three items which content is the same for all inversion modules: * Runs * Log * Status Plus ...

New page

This menu lets the user hide or show various tools used along inversions.

It contains at least three items which content is the same for all inversion modules:
* Runs
* Log
* Status
Plus eventually two others for most of the inversion modules which contents depends upon the selected module:
* Targets
* Parameters

'''Runs''' is a table that gathers all runs created so far in the environment. This is the master table where you can select runs. This selection is used by menus [[Dinver:Menus:View|View]] and [[Dinver:Menus:Runs|Runs]].

'''Log''' has one tab per inversion run plus a general tab. All outputs generated during initialization and during inversion itself are stored there with one log per run. This is the good place to look for when you encounter errors or unexpected behaviors.

'''Status''' shows dynamic information about running inversion.

← Older revision		Revision as of 21:13, 26 November 2008
Line 1:		Line 1:
−	This menu lets the user hide or show various tools used along inversions.	+	This menu lets the user hide or show various tools used along inversions. Closing a tool panel or hiding it with the menu is strictly equivalent. In any case, if a tool is not visible, you can always get it back thanks to this menu.

	It contains at least three items which content is the same for all inversion modules:		It contains at least three items which content is the same for all inversion modules:

@@ Line 9: / Line 9: @@
 * Parameters
-'''Runs''' is a table that gathers all runs created so far in the environment. This is the master table where you can select runs. This selection is used by menus [[Dinver:Menus:View|View]] and [[Dinver:Menus:Runs|Runs]].
+'''Runs''' is a table that gathers all runs created so far in the environment. This is the master table where you can select runs. This selection is used by menus [[Dinver: View menu|View]] and [[Dinver: Runs menu|Runs]].
 '''Log''' has one tab per inversion run plus a general tab. All outputs generated during initialization and during inversion itself are stored there with one log per run. This is the good place to look for when you encounter errors or unexpected behaviors.
 '''Status''' shows dynamic information about running inversion.

← Older revision	Revision as of 13:12, 12 March 2010
(No difference)

@@ Line 1: / Line 1: @@
 This menu lets the user hide or show various tools used along inversions. Closing a tool panel or hiding it with the menu is strictly equivalent. In any case, if a tool is not visible, you can always get it back thanks to this menu.
-It contains at least three items which content is the same for all inversion modules:
+It contains at least three items which contents are the same for all inversion modules:
 * Runs
 * Log
 * Status
-Plus eventually two others for most of the inversion modules which contents depends upon the selected module:
+Plus eventually two others for most of the inversion modules which contents depend upon the selected module:
 * Targets
 * Parameters